BS EN 10106:2015 – TC:2020 Edition
$186.33
Tracked Changes. Cold rolled non-oriented electrical steel strip and sheet delivered in the fully processed state
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 53 |
This European Standard specifies cold-rolled non-oriented electrical steel strip and sheet in nominal thicknesses of 0,35 mm, 0,50 mm, 0,65 mm and 1,00 mm. In particular, it specifies general requirements, the magnetic properties, geometric characteristics and tolerances, technological characteristics as well as the inspection procedure. This European Standard applies to materials supplied in the fully annealed condition intended for the construction of magnetic circuits. It does not apply to semi-processed material. These magnetic materials correspond to IEC 60404 1:2000, C.2.3.2.1.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 31 | Contents Page |
| 33 | European foreword |
| 34 | 1 Scope 2 Normative references 3 Terms and definitions |
| 35 | 4 Classification and designation 4.1 Classification 4.2 Designation 5 Information supplied by the purchaser 5.1 Mandatory information |
| 36 | 5.2 Options 5.3 Example of an order 6 General requirements 6.1 Production process 6.2 Form of supply |
| 37 | 6.3 Delivery condition 6.4 Surface condition 6.5 Suitability for cutting 7 Technical requirements 7.1 Magnetic properties 7.1.1 General 7.1.2 Magnetic polarization |
| 38 | 7.1.3 Specific total loss 7.1.4 Anisotropy of loss Table 1 — Technological and magnetic properties |
| 39 | 7.2 Geometric characteristics and tolerances 7.2.1 Thickness |
| 40 | 7.2.2 Width Table 2 — Tolerances for material supplied with trimmed edges |
| 41 | 7.2.3 Length 7.2.4 Edge camber 7.2.5 Flatness (wave factor) 7.2.6 Residual curvature 7.3 Technological characteristics 7.3.1 Density 7.3.2 Stacking factor 7.3.3 Number of bends 7.3.4 Internal stresses |
| 42 | 8 Inspection and testing 8.1 General 8.2 Selection of samples 8.3 Preparation of test specimens 8.3.1 Magnetic properties |
| 43 | 8.3.2 Geometrical characteristics and tolerances 8.3.3 Technological characteristics 8.3.3.1 Stacking factor 8.3.3.2 Number of bends 8.3.3.3 Internal stresses 8.4 Test methods 8.4.1 General 8.4.2 Magnetic properties 8.4.2.1 Magnetic polarization and specific total loss 8.4.2.2 Anisotropy of loss |
| 44 | 8.4.3 Geometrical characteristics and tolerances 8.4.3.1 Thickness 8.4.3.2 Width 8.4.3.3 Edge camber 8.4.3.4 Flatness (wave factor) 8.4.3.5 Residual curvature 8.4.4 Technological characteristics 8.4.4.1 Stacking factor 8.4.4.2 Number of bends |
| 45 | 8.4.4.3 Internal stresses 8.5 Retests 9 Marking, labelling and packaging 10 Complaints |
| 46 | Annex A (normative) Options |
| 47 | Annex B (informative) Non-specified magnetic properties Table B.1 — Specific total loss for conditions deviating from Table 1 |
| 48 | Annex C (informative) Density determination |
| 49 | Annex D (informative) Minimum stacking factor for coated products Table D.1 — Minimum stacking factor for coated products according to coating thicknesses |
| 50 | Annex E (informative) Changes to the previous version EN 10106:2007 |
| 51 | Bibliography |
